|
EFFECTS
EQUO - Morphing Graphic Equalizer Learn anything about roulette strategie dutzend at Casinoclub.com!
EQUO is an advanced morphing graphic equalizer
plugin. EQUO is particularly suited to live or automated tweaking
during a performance. The main display contains both the EQ
(VOL) and EQ (PAN) controls so that
sounds can not only be shaped according to frequency content, but
panning can be applied on specific frequency basis. Further, One
Master EQ shape and then a further 8
separate EQ/PAN shapes may be set and then these EQ shapes
can be smoothly morphed using the Morph knob. An
alternative to EQUO is Fruity Parametric EQ.
Parameters
Morph Section
- Shift (Band Shift) - Turning the knob to the
right will move the current EQ shape to the higher frequencies,
moving the knob to the left shifts the current shape to the lower
frequencies. Try automating this parameter.
- Mix (Band mix) - By default, applies 100% of
the selected EQ shape to the (knob full right). Moving the knob
fully left will apply -100% of the current shape (invert it). The
12'Oclock position applies 0% EQ.
- Morph (Between Banks)- Morphs (blends) between
banks 1 (knob fully left) to 8 (knob fully right). For this
function to have an effect you must set different EQ curves on each
bank.
- Smooth (Motion Smoothness) - Sets how quickly
changes to EQUO settings can happen. This is like an inertia effect
for knobs.
- Vol - Main output volume.
Setup Section
Contains controls to set the routing and audio quality
- Send only | Send - Mutes the direct output
from EQUO in the present Mixer channel. The LED display window
shows which send mixer track EQUO is set to. The Send window is not
operational if EQUO is in the Master Mixer channel to avoid a
feedback loop.
- Add mode - Normally EQUO band-slices the
incoming audio, effects it and recombines the audio at the output.
The band-slicing and recombination process introduces subtle
changes to the input audio, even when no EQ is applied (the EQ
bands are flat). Add mode combines (adds) the sound of EQUO to the
original input rather than replacing it (as normal) to avoid these
subtle effects. However, in add mode an EQ band set to minimum will
allow the original signal to pass.
- Over sample - Engages 2X oversampling for
higher audio quality.
- BW (Band Width) - Changes the bandwidth of the
EQUO bands. Simply adjust for the most pleasing sound.
Main Display
There are several controls available from the main screen that
will change the way you can shape the EQ or PAN settings.
- Options Menu -
Contains three options, Random
Curve, that produces a random EQ or PAN cuve, surprisingly
:) Flat Line that resets the current EQ curve to
the default state and Interpolate 1 to 8, this
allows you to set a EQ or PAN curve in bank 1 and 8 and then EQUO
will create the intermediate steps in-between on banks 2 to 7.
- Drawing modes - There are three drawing modes
available by clicking the appropriate icon. Pencil
mode
allows you to move
individual EQ or PAN bands with precision. Line
mode Left click and drag the
mouse to create straight lines. Curve mode
Left click and drag the mouse to
create smooth curves.
- Analyze - When the Analyze button is held,
EQUO will average the frequency spectrum of the incoming signal
(over the duration the button is held) and upon release create an
EQ curve antagonistic to that signal. The interaction of the
analyzed curve can be varied from antagonistic (cut) though to
complimentary (boost) with the MIX knob.
NOTE: Bands 40 Hz and below are not included in
the 'Analyze' function as they 'muddy' the mix, set them manually
if you require sub-bass EQ.
- EQ/PAN On/Off/Locked - Clicking the light-blue
box at the top of an EQ band will switch through the sequence 1 -
Band OFF, 2 - Band Locked, 3 - Band Enabled (default).

- Adjusting bands - Clicking in the display area
will activate the band under your mouse pointer. Move the band up
and down as required. Consider these bands to be the sliders on a
Graphic equalizer and you have a good idea of the basic interface.
The image below shows EQUO in curve mode tracking an upward
movement of the mouse, to move individual bands set EQUO to pencil
mode.

- Bank M, 1 to 8 - Select these to individually
set the Master bank or Banks 1 to
8. The Master bank is applied to the
final output of the plugin and is not used in the morphing sequence
between banks.
- VOL/PAN/SEND - Switches, determine if the
action in the main EQ area affect, VOL (Volume) -
the standard EQ volume as a function of frequency,
PAN - The stereo panning of the selected frequency
or Send - The send levels for the selected
frequencies.
Plugin Credits: Didier Dambrin.
|